Skip to content

Atosa ATFS-40-LP 16-Inch 40 lb Propane Deep Fryer, 90,000 BTU, 3 Burners

Atosa ATFS-40-LP 16-Inch 40 lb Propane Deep Fryer, 90,000 BTU, 3 Burners

The Atosa ATFS-40-LP is a 15-3/5" wide floor model fryer for propane that holds 40 lb of oil. It has 3 burners with 90,000 BTU in total and holds 200°F to 400°F.

At a Glance

  • Size: 15-3/5" W x 30-1/10" D x 44-2/5" H
  • Oil capacity: 40 lb
  • Gas: propane, 3 burners, 90,000 BTU total
  • Temperature: 200°F to 400°F, millivolt thermostat
  • Baskets: two (2) nickel plated baskets with coated handles, basket hanger
  • Mobility: four (4) casters standard
  • Certifications: cETLus, ETL-Sanitation
  • Warranty: 1 year parts and labor

Most units ship within one business day from our warehouse with free freight to the lower 48.

A 40 lb Commercial Propane Fryer

This commercial propane fryer holds 40 lb of oil and has three burners with 90,000 BTU in total. It is 15-3/5" wide, comes with two baskets, and rolls on four casters.

Is the ATFS-40-LP the Right Size for Your Line?

The ATFS-40-LP holds 40 lb of oil over 3 burners at 30,000 BTU each, 90,000 BTU in total. That works out to about 2,250 BTU per pound of oil.

Plan roughly 27-3/5" x 36-1/10" of floor for this 131 lb propane fryer once you add the 6" side and back clearance from Atosa's manual. The cabinet itself is 15-3/5" wide, matching the other 16" ATFS models.

More oil on propane without more width: the ATFS-50-LP adds a fourth 30,000 BTU burner and holds 50 lb. Running on natural gas instead? The ATFS-40-NG is the same fryer with 34,000 BTU burners (102,000 total) and a 4" W.C. regulator instead of 10" W.C.

Good For

  • Restaurants on propane: fries, chicken and sides from 40 lb of oil
  • Pubs and taverns: wings and appetizers at 90,000 BTU
  • Taquerias: chips, taco shells and churros
  • A 16" opening on the line: 15-3/5" wide, rolls on four casters
  • Kitchens without a natural gas line: runs on propane

Built for Daily Commercial Use

  • Stainless steel exterior and interior
  • Welded stainless steel tank
  • Heavy duty burners with a standing flame and standby pilots
  • Millivolt thermostat that holds the temperature you set, from 200°F to 400°F
  • Oil cooling zone in the bottom of the tank catches food bits and helps oil last longer
  • Safety valve with an automatic voltage stabilizing function
  • Self-reset high temperature limit
  • Two (2) nickel plated baskets with coated handles and a basket hanger
  • 3/4" NPT rear gas connection and regulator
  • Four (4) casters standard

Pick the Right Fryer

Model Gas Oil Burners Total BTU Width
ATFS-35ES-NG Natural gas 35 lb 3 60,000 15-3/5"
ATFS-35ES-LP Propane 35 lb 3 60,000 15-3/5"
ATFS-40-NG Natural gas 40 lb 3 102,000 15-3/5"
ATFS-40-LP (this model) Propane 40 lb 3 90,000 15-3/5"
ATFS-50-NG Natural gas 50 lb 4 136,000 15-3/5"
ATFS-50-LP Propane 50 lb 4 120,000 15-3/5"
ATFS-75-NG Natural gas 75 lb 5 170,000 21-1/10"
ATFS-75-LP Propane 75 lb 5 150,000 21-1/10"

Need natural gas? See the Atosa ATFS-40-NG, the same fryer for natural gas. Want ENERGY STAR? See the Atosa ATFS-35ES-LP.

Optional accessories: fryer cover 21201001019, splash guard 21101001047, joiner strip 21101001046, mesh fryer screen R06018000069 and leg kit 301110006.

Shop all commercial deep fryers, including propane and 40 lb models.

Specifications

Spec Detail
Configuration Floor model propane deep fryer
Oil capacity 40 lb
Gas type Propane (LP)
Burners 3, independent manual control
BTU per burner 30,000
Total BTU 90,000
Gas pressure (regulator) 10" W.C.
Gas connection 3/4" NPT, rear, with regulator
Burner nozzle (manual) #52
Temperature range 200°F to 400°F
Thermostat Millivolt
Safety Self-reset high temperature limit; safety valve with automatic voltage stabilizing
Baskets (2) nickel plated, coated handles
Basket size 13-3/10" x 6-1/2" x 5-9/10"
Cooling zone Yes, bottom of tank
Construction Stainless steel exterior, interior and welded tank
Casters (4) standard; leg kit 301110006 optional
Exterior dimensions 15-3/5" W x 30-1/10" D x 44-2/5" H
Net weight 131 lb
Shipping weight 160 lb
Warranty 1 year parts and labor
Certifications cETLus, ETL-Sanitation; conforms to NSF/ANSI 4 and ANSI Z83.11b; certified to CSA 1.8b

Before You Order

  • This is the propane model. Order the ATFS-40-NG for natural gas.
  • Gas: 3/4" NPT rear connection with a regulator. Atosa sets it at 10" W.C. for propane.
  • Check your space: the ATFS-40-LP is 15-3/5" wide, 30-1/10" deep and 44-2/5" tall, and weighs 131 lb.
  • Atosa's manual says to leave at least 6" on both sides and the back (about 27-3/5" of width and 36-1/10" of depth for the ATFS-40-LP), and to install the fryer under an exhaust hood as local code requires.
  • Atosa's manual says an authorized, licensed technician must install it, and that it is not for outdoor use.
  • Add oil or solid shortening before you light the main burners, and never fill above the oil level line. Melt shortening at the lowest setting.

Cleaning and Care

  • Before first use, wipe the fryer with a mild detergent.
  • To boil out the tank, fill it with water and detergent below the oil line, heat 5 to 10 minutes, let it soak, wipe it down, then drain and rinse. For tablets, see the Atosa ATTAB1 boil out tablets.
  • Do not use a wire brush on the tank, and do not hose down or pressure wash the fryer.
  • Atosa says to have the flue cleaned every 3 to 6 months, and to have the fryer checked once a year, by a qualified technician.

Atosa ATFS-40-LP FAQ

What size is the Atosa ATFS-40-LP?

The ATFS-40-LP is 15-3/5" wide, 30-1/10" deep and 44-2/5" tall. It weighs 131 lb (160 lb shipping weight).

How much oil does the ATFS-40-LP hold?

40 lb.

How many BTU is the ATFS-40-LP?

90,000 BTU total: 3 burners at 30,000 BTU each, on propane.

What temperature range does the ATFS-40-LP have?

200°F to 400°F, with a millivolt thermostat that holds the temperature you set.

What gas connection does the ATFS-40-LP need?

A 3/4" NPT rear connection. It has a regulator set at 10" W.C. for propane.

Does the ATFS-40-LP come with baskets?

Yes, two. Each nickel plated basket measures 13-3/10" x 6-1/2" x 5-9/10" and has a coated handle, and a basket hanger is included.

Does the ATFS-40-LP have legs or casters?

Four casters come standard, which makes the 131 lb propane fryer easier to move. Prefer legs? Add the optional 301110006 leg kit.

How much space does the ATFS-40-LP need around it?

At least 6" on both sides and the back, per Atosa's manual. That means a floor area of roughly 27-3/5" x 36-1/10" for the ATFS-40-LP.

What certifications does the ATFS-40-LP have?

cETLus, ETL-Sanitation; conforms to NSF/ANSI 4 and ANSI Z83.11b; certified to CSA 1.8b. Unlike the ATFS-35ES, it is not ENERGY STAR rated.

What warranty comes with the ATFS-40-LP?

1 year parts and labor. Genuine ATFS-40 replacement parts are listed in the parts section on this page.

Is the ATFS-40-LP big enough, or do I need the ATFS-50-LP?

The ATFS-40-LP suits a lighter frying menu with 40 lb of oil on 3 burners. If you fry bigger batches, the ATFS-50-LP adds 10 lb of oil and a fourth burner (120,000 BTU) and still fits the same 15-3/5" space.

What is the difference between the ATFS-40-LP and the ATFS-40-NG?

The ATFS-40-LP runs on propane: 30,000 BTU burners, 90,000 BTU total and a 10" W.C. regulator. The ATFS-40-NG runs on natural gas, with 34,000 BTU burners and 102,000 BTU total. Size, oil capacity and baskets are the same. Order the one that matches your gas supply.

Spec Sheet and Manual

Download the Atosa ATFS-40-LP spec sheet (PDF, Rev. 07/25)

Download the Atosa ATFS-40/50/75 fryer manual (PDF)

Genuine Replacement Parts for the ATFS-40

Keep your ATFS-40 fryer running like new with genuine OEM Atosa service parts. Common wear components we stock include the 301030005 hi limit thermostat, the 301030004 thermostat, the 301030006 thermocouple, the 301140002 knob, and the 301040003 burner orifice. Browse the complete Atosa parts catalog or reference the Atosa parts manuals for compatibility.

ATFS-40 Parts & Service

For OEM replacement parts for the ATFS-40, see the ATFS-40 parts list, with part numbers and quantities from Atosa's exploded-view diagram. Parts lists for every model are on the Atosa parts lists index.

The Atosa ATFS-40-LP is a 40 lb propane floor fryer with 3 burners and 90,000 BTU of total input. It is 15-3/5" wide, 30-1/10" deep and 44-2/5" tall, rolls on four casters, and comes with two nickel plated baskets. It is the size most kitchens start with, so this guide also shows when to step down to the 35ES or up to the 50.

Where the ATFS-40 Fits in the ATFS Line

Atosa makes the ATFS in 35, 40, 50 and 75 lb sizes. The 40 is the standard 3-burner model. Its burners are rated at 30,000 BTU each, for 90,000 BTU in total. That is more input than the ATFS-35ES-LP, which runs at 60,000 BTU and is built to ENERGY STAR, in the same 15-3/5" width.

The 40 suits restaurants, bars and diners that fry fries, wings, chicken and sides through the day but do not run a fry-heavy menu. If you are already close to the limit of 40 lb, the ATFS-50-LP adds 10 lb of oil and a fourth burner without taking more width. For a fry-heavy menu, look at the ATFS-75-LP.

Sizing the ATFS-40 to Your Volume

Atosa does not publish an hourly production rating. Using the common estimate of 1.5 to 2 times oil capacity per hour, a 40 lb fryer tops out around 60 to 80 lb of food per hour, with fries at the high end and breaded items at the low end.

On propane, three 30,000 BTU burners put about 2,250 BTU behind each pound of oil, enough for a steady flow of fries, wings and sides. Count the fried food you sell in your busiest hour and add 20 to 25 percent. If that lands near the top of the range, or the menu leans on breaded bone-in chicken, the ATFS-50-LP adds a fourth burner in the same width. If it lands well under 50 lb and gas cost matters more, look at the ATFS-35ES-LP.

This Is the Propane Model

The ATFS-40-LP is built for propane only. Each ATFS size comes as a separate natural gas model and a separate propane model, with different burner nozzles and regulator settings. On this model Atosa lists #52 burner nozzles and sets the regulator at 10" W.C. If your kitchen runs on natural gas, order the ATFS-40-NG instead.

The propane model is rated at 90,000 BTU and the natural gas model at 102,000 BTU. Atosa rates the burners at 34,000 BTU each on natural gas and 30,000 BTU each on propane, so the two versions have the same number of burners but different listed input.

Propane kitchens need a supply that can keep up with the fryer and any other propane equipment on the same line. Your propane supplier or gas installer should confirm the tank, regulator and line size for the total BTU you will run.

Space, Clearance and Height

The ATFS-40-LP is 15-3/5" wide, 30-1/10" deep and 44-2/5" tall, and weighs 131 lb (160 lb shipping). Atosa's manual says to leave at least 6" of clearance on both sides and the back. That means planning about 27-3/5" of width and 36-1/10" of depth for the ATFS-40. The fryer must go under a ventilation hood that meets your local code, and it is not for outdoor use.

It comes with four casters as standard, so you can roll it out for cleaning. Atosa also lists an optional leg kit, 301110006, if you would rather stand it on legs. Because it rolls, connect it with a flexible gas hose kit that includes a restraining cable (see the gas hookup section below).

Baskets and Tank

The ATFS-40 comes with two nickel plated baskets, 13-3/10" x 6-1/2" x 5-9/10", with coated handles, plus a basket hanger. The 75 lb ATFS uses wider 9-1/2" baskets. On this size you get the 6-1/2" basket, the same as the other 15-3/5" models, so baskets interchange across a line of 35, 40 and 50 lb fryers.

The tank is welded stainless steel with a cool zone at the bottom. Crumbs and breading settle into the cool zone, below the hottest oil, which helps slow how fast they burn and darken the oil. Temperature runs from 200°F to 400°F on a millivolt thermostat, with a self-reset high temperature limit.

Filtering the Oil

For a 40 lb fryer, the Atosa FPOF-50 portable filter holds a full drain: it takes up to 50 lb of oil. It rolls under the fryer drain, filters the oil and pumps it back through a 5' high temperature hose. It uses FP-1324-5 filter paper, 13-1/2" x 24", 100 sheets per box.

If you run several fryers, or plan to add a 75 lb fryer later, the larger FPOF-80 holds 80 lb and uses FP-1728-5 paper.

Filtering often, many kitchens do it daily at close, removes crumbs before they burn and keeps the oil usable longer. Always follow the filter and fryer manuals for safe draining temperatures.

Gas Hookup

The ATFS-40-LP has a 3/4" NPT gas connection at the rear, with the regulator. Both 3/4" x 48" hose kits on this site fit that connection size, and both are rated above this fryer's 90,000 BTU:

  • Atosa WA300001: 180,000 BTU per hour, with a quick disconnect, gas valve, restraining cable kit and two 90° elbows.
  • BK Resources BKG-GHC-7548-SCK3: 184,000 BTU per hour as BK rates it with the shut-off valve and quick connect, with a 5 year warranty on the hose.

Measure from the gas outlet to the fryer's gas inlet before you order, so the 48" hose reaches without stretching or sharp bends. Keep the restraining cable connected. Have a qualified gas installer make the connection, check for leaks and confirm the setup meets local code.

Cleaning and Care

Before first use, wipe the fryer with a mild detergent. Boil out the tank when buildup appears and whenever you change the oil. Fill it with water and detergent below the oil line, heat, soak, then drain and rinse. Atosa ATTAB1 boil-out tablets are low foam and made for this job. Do not use a wire brush on the tank, and never hose down or pressure wash the fryer.

Atosa says to have the flue cleaned every 3 to 6 months. The fryer has a 1 year parts and labor warranty.

Menu Fit: What the ATFS-40 Fries Well

The 40 lb tank is the all-round size for most restaurants: fries, wings, chicken tenders, fish and appetizers. With two baskets you can run two orders at once or keep one basket draining while the other cooks.

FoodTypical starting temperature
Frozen fries350°F
Fresh-cut friesBlanch at 300-325°F, finish at 350-375°F
Wings350-375°F
Breaded bone-in chicken325-350°F
Fish fillets and shrimp350-375°F
Tortilla chips and taco shells350°F
Frozen appetizers350°F

These are common kitchen starting points, not Atosa settings. Follow the directions from your food supplier and your local food safety rules for internal temperatures.

The ATFS thermostat runs from 200°F to 400°F, which covers all of these.

Planning the Fry Line Around the ATFS-40

Kitchens often weigh one large fryer against two smaller ones. Here is how the ATFS-40 compares, using Atosa's listed widths and oil capacities:

OptionTotal widthTotal oil
two ATFS-40 fryers31-1/5"80 lb
one ATFS-7521-1/10"75 lb

Two 40s take about 10" more width than one 75, but you get two separate oils and one fryer keeps working while the other is filtered or boiled out. Widths do not include the 6" side clearance Atosa calls for, so add that to any plan.

Setting Up on Day One

  1. Check the data plate: this unit is built for propane. Do not connect it to the other gas type.
  2. Roll it into place under the hood, level it, and keep the 6" clearance on the sides and back.
  3. Have a qualified installer connect a 3/4" flexible hose kit with the restraining cable, then leak test every joint.
  4. Wipe the tank and fryer with a mild detergent, rinse and dry fully, as the Atosa manual says before first use.
  5. Fill the tank to the oil line with 40 lb of oil before lighting. Never heat an empty tank.
  6. Light the pilot following the lighting steps in the manual, then set the thermostat and let the oil come up to temperature before the first drop.

Two Baskets, One 40 lb Fill

With two baskets the 40 can cook one order while the other drains, which is how most kitchens get the most out of it. The tradeoff is that everything you fry shares the same 40 lb of oil.

  • Fish and heavily breaded items wear oil out faster and can flavor fries. If you sell a lot of both, a second fryer for fish keeps the main oil cleaner.
  • The FPOF-50 holds a full 40 lb drain with 10 lb to spare. Filter at least once a day.
  • Shake ice off frozen product before the drop. Water breaks oil down and makes it spatter.
  • Turn the thermostat down between rushes instead of holding frying heat all afternoon.

Change the oil when it turns dark, smokes at normal frying temperature, foams heavily, or tastes off, and boil out with ATTAB1 tablets at each change.

What a Complete ATFS-40 Setup Includes

  • The fryer, in the propane version.
  • A 3/4" gas hose kit with restraining cable: Atosa WA300001 or BK Resources BKG-GHC-7548-SCK3.
  • A portable filter sized for 40 lb of oil: the FPOF-50.
  • Filter paper for that filter: FP-1324-5.
  • ATTAB1 boil-out tablets for tank cleaning.
  • 40 lb of frying oil for the first fill, plus a spare fill on the shelf.

Before You Order

  • Gas type: this is the propane model. For natural gas, order the ATFS-40-NG.
  • Space: 15-3/5" wide plus 6" on each side and the back, about 27-3/5" x 36-1/10".
  • Hood: the fryer must sit under a hood that meets your local code.
  • Gas hose: a 3/4" flexible hose kit with a restraining cable, sized to your run.
  • Filter: the FPOF-50 with FP-1324-5 paper.
  • Boil-out: ATTAB1 tablets for tank cleaning.

Common Questions

Can I convert the ATFS-40-LP to natural gas?

Order the ATFS-40-NG for natural gas. Each model has its own burner nozzles and regulator setting. If you need to change gas type later, ask a qualified technician and Atosa about the correct parts and procedure.

Should I get the 40 or the 50?

Both are 15-3/5" wide. The 50 adds 10 lb of oil and a fourth burner. If your busiest hour is near the top of the 40's range, the ATFS-50-LP gives you room to grow in the same space.

Can I fry fish and fries in the same ATFS-40?

You can, but they share the oil, so fries can pick up fish flavor and the oil wears out sooner. Kitchens that sell a lot of both often add a second fryer, such as the ATFS-35ES-LP, just for fish.

Will the ATFS-40 fit a 16" opening?

The fryer is 15-3/5" wide, but Atosa calls for 6" on both sides and the back, so plan about 27-3/5" of width. Check that with your hood and local code before you order.

How much oil does the ATFS-40 take?

Atosa rates the tank at 40 lb. Fill to the oil line marked in the tank, and keep a spare fill on hand.

Do I need a hood?

Commercial gas fryers are normally installed under a ventilation hood with fire suppression. Your local code official and hood installer set the exact requirements.

To see the current price and order, use the "See Price & Buy at The Restaurant Warehouse" button above. Questions about sizing or gas setup? Call or text (206) 419-5801.

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare